![]() Most common cause will be bad or fake SD cards. Fake / Bad SD cards or your iTunes is too large for the iPod. iTunes will apply these settings every time that iPod is connected.Īfter syncing and ejecting, the iPod shows no music OR needs restoring again Under the larger iPod icon is menu of various media types – enter each one and select what you want synced to the iPod.įinally click on Apply and Sync. You need to click on the iPod icon on the main iTunes screen. The latest version of iTunes by default do not sync anything to a newly restored iPod. The Apple OS on these devices operates LBA28 addressing which limits access to 127GiB total storage.Īfter restoring iTunes does not sync anything to the iPod These are the metal faced units which came in 80GB / 120GB and a thicker 160GB capacity. This is due to having an 6th Gen iPod Classic. Post Install ProblemsĪfter restoring iPod only shows 127GB / 128GB or 137GB Open iTunes and attempt restore, if this does not work – eject the iPod, disconnect from the computer, and reset the iPod – then reconnect to the computer and try again. Here you can delete/partition/erase and reformat the iPod – you can either format to FAT32 or MAC OS extended (Journaled).Ĭheck that you can read/write to the iPod drive. On MACs the iPod drive can be found in the disk utility. You may need to use an 3rd party disk formatter if windows is not able to format to full capacity of the iPod. Now you can format the iPod ‘drive’ and check you can read/write to it correctly. Locate Disk Management, and assign driver letter to the iPod device. On Windows machines, the iPod will appear in the file explorer – if it does not it is possible that no drive letter has been assigned to it. The iPod ‘drive’ should appear on the computer. ![]() Cards will work installed one at a time, but more than one causes RED X.Quickly switch to holding down Forward+Play/Pause until iPod enters diskmode Reports of Sandisk cards causing RED X when more than one used in the iFlash-Quad. MicroSD (SDXC) cards reported by iFlash users : Manufacturer / Brand Be wary of cheap, high capacity cards – If it looks too good to be true – then it is fake! We always suggest testing the SD card fully using something like H2Testw.įullsize SD (SDXC) cards reported by iFlash users : Manufacturer / Brand Tip: MicroSD market is full of fake and mislabelled cards – try to purchase cards which the seller has obtained directly from the manufacturer. We suggest buying the fastest card in your budget as they tend to have faster access times and better quality memory chips. User Reported working SD cards (updated: 5th January 2022)Īll modern UHS-I U1 and U3 cards will generally work ok. IPod is now ready to restore & sync using iTunes. Slide battery cable in to the connector and push down the black latch to lock the ribbon in place. Once the foam has been attached, the iPod is ready to be closed up. Attach 2nd Foam on top of 1st foam if installing in to a thick back iPod. Use 1 piece of foam for thin case back iPods. Place foam pad on the marked section on board. Install iFlash-Dual into iPod, making sure the ribbon is fully home and the black bar is locked down. Install SD cards in to iFlash-Dual – use socket SD1 if installing only 1 SD card. iPod is ready to accept the iFlash board. Remove all rubber bumpers and strips from the iPods if any remain after the HDD is removed. Gently lift the black bar to release the ribbon from the HDD. Rest the front and back side by side, be careful to not cause too much stress on the headphone ribbon. I suggest watching some iPod opening videos on the internet.īefore pulling the case apart, release the battery cable – lift the black lock bar -or- gently using even pressure pull up the battery ribbon away from the connector. Using suitable tools, release the holding clips, making your way around the case till it opens.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |